Skip to content

Started your trial? Get the app and log in with the same account.

How to do a field-level hazard assessment

A few minutes at the work, before the work: what could hurt someone on this task today, and what you’ll do about each hazard.

Safety6 min readUpdated

A field-level hazard assessment is a short written check, done by the crew at the work, right before the work: what could hurt someone on this task today, and what you’ll do about it.

It isn’t the safety manual written once in the office. It’s for this task, in this spot, in today’s conditions, by the people about to do it.

Done properly, it takes a few minutes and catches the hazard that wasn’t there yesterday: the trench that took on water overnight, the new hole in the deck, the crane working next door.

When to do one

Do one before a task starts, and again whenever something changes:

  • At the start of each shift, for the work planned that day.
  • When the crew starts a new task, or moves to a new area.
  • When conditions change: the weather, another trade starting nearby, a new piece of equipment.
  • When someone new joins the crew.
  • After a near miss, before the work starts again.

If the task is the same as yesterday, in the same spot, the assessment can be short. It still gets done, because yesterday’s conditions aren’t today’s.

Walk the task and list the hazards

Don’t fill in the form at the truck. Go to where the work will happen, with the people who’ll do it, and walk through the job step by step.

  1. Break the task into steps. Cutting in a window opening is: set up, mark, cut, take out the section, frame it, clean up.
  2. At each step, ask what could go wrong. What could fall, cut, crush, burn, shock or trip someone? What’s above, below and beside the work?
  3. Look at the area, not only the task. Overhead lines, openings, traffic, other trades, the public and the weather.
  4. Ask the crew. Whoever did this task last week knows what nearly went wrong.

Write each hazard down in plain words, one to a line. “Falling off the scaffold while setting the window” is a hazard. “Heights” is a heading.

If your company rates each hazard for how bad and how likely it is, rate it now. Either way, the worst ones get dealt with first.

Pick controls in the right order

For each hazard, decide how you’ll control it. Work down this list, the hierarchy of controls, and use the highest one that’s practical. The top ones work without anyone having to remember them.

  1. Eliminate it. Take the hazard away: assemble the truss on the ground instead of at height, or make the cut in the shop.
  2. Substitute it. Use something less dangerous: a battery saw instead of a cord across wet ground, a lighter product, a lift instead of a ladder.
  3. Engineer it out. Put something between people and the hazard: guardrails, covers on openings, shoring in the trench, a saw with water or dust extraction.
  4. Control it with rules. Change how the work is done: a permit, a spotter, a barricade and a sign, a no-go zone under the load.
  5. Protect the person. The harness, the respirator, the glasses, the hearing protection. It’s last because it only works if it fits, it’s worn and it suits the hazard.

Most hazards need more than one. A trench gets shoring, a ladder to get out, a barricade at the edge and hard hats.

Write each control beside its hazard, exactly. “Use fall protection” isn’t a control. “Harness tied off to the ridge anchor, checked by Dana before anyone goes up” is.

Check what the law requires

Some provinces, like Alberta, require a written hazard assessment before work begins, with the workers taking part, and many general contractors ask for one on their sites. Check the rules for your jobs.

Sign it, and review it when the job changes

Everyone doing the task reads the assessment, or has it read to them, and signs it before they start. Their signature says: I know the hazards and the controls, and I’ll work that way.

  • The crew doing the task, each in their own name.
  • The foreman, who checks that the controls are really in place before work starts.
  • Anyone who joins later, before they start, including a sub’s crew working in the same area.

Keep it at the work, where the crew can see it, not on the dash of the truck.

When anything changes, like a new step, a new area, new equipment, the weather or a new person, stop and add it: what changed, the new control, and new signatures.

If a control can’t be put in place, the task doesn’t start. It starts when the assessment says how it will be done safely.

File it with the job at the end of the day. Read a week of them now and then: the hazard that shows up on every one is the one to fix for good.

How it differs from a toolbox talk

The two are easy to mix up, and a good site needs both.

  • A [toolbox talk](/guides/toolbox-talks) is a short briefing for the whole crew on one safety topic, like ladders, silica or heat. It teaches.
  • A hazard assessment is a check of one task, in one place, today, by the people about to do it. It plans the work.

A good morning often has both: the talk at the start of the shift, then each crew walks its own task and writes its assessment before it starts.

Use each to feed the other. A hazard that keeps turning up on the assessments makes a good next talk, and the fix from an incident report belongs on the next assessment for that task.

How CrewLog does it

CrewLog has no hazard assessment form of its own. You can still keep the review, and who signed it, with the rest of your safety record:

  1. Make it one of your company’s talks. Add a talk with your assessment’s questions as its points to cover, and your blank form as its handout, a PDF or a photo.
  2. Hold it at the work. The foreman picks the job and that talk, picks or types the hazards covered and notes the controls. Everyone signs on one phone by tapping their name, and a sub or a visitor types theirs.
  3. Turn fixes into actions. A control that isn’t in place yet becomes a corrective action on the job, with an owner and a due date.

The hazards and the signatures, on one record. A talk held at the work: the hazards covered, the controls in its notes, each name tapped on one phone.

Each signature is time-stamped, and a talk entered after the day says how many days later it was recorded.

A hazard covered in three or more talks in 90 days is listed on the Safety overview as one that keeps coming up. A hazard you keep briefing is one that hasn’t been fixed.

If your crew fills in a paper form, a photo of it can go on the job from the Field screen.

Toolbox talks, your company’s own talks and corrective actions are on every plan, from $39 a month. Compare the plans.

More on safety on the features page.

More guides

All guides

Get the hazards and the signatures on one phone.

Hold the review as one of your own talks, sign it by name, and give every fix an owner and a date.

14 days free, no card to start. Then $39 to $179 a month for the whole company.